|
|
| Home >> Products >> Beater Addition Jointing Sheet |
| Beater Addition Jointing Sheet |
| -------------------------------------------------------------------------------------------------------------------------------------- |
| |
|
|
|
|
|
| |
| 3D 6100 - Beater Addition Jointing Sheet |
 Material Description |
| 3D-6100 is a comparatively low density, high performance gasket material designed for elevated temperature applications. It is composed of a blend of asbestos fibre, inorganic fillers & nitrile binder. This provides the material with good torque retentions when combined with a metal core. It's low density makes it ideally suitable for perforated core applications & the high compressibility imparts good flange confirmability. This material is available in light grey, red or green shade. |
|
 |
| Physical Properties |
| |
Unit |
Typical Value |
| Density |
(gm/cc) |
1.0 |
| Compressibility |
(%) |
4-0 |
| Recovery |
(%) |
26 |
| Tensile Strength |
(kg/sq.cm) |
48 |
|
| Fluid Immersions |
| WEIGHT INCREASE |
| A.S.T.M. Oil 3,5hrs.150° C. |
(%) |
49 |
| A.S.T.M. Fuel B, 5hrs Room Temp |
(%) |
45 |
| 50% Anti Freeze + 50% Distilled Water 5, hrs, Room Temp. |
(%) |
60 |
|
|
| Thickness Increases |
| A.S.T.M. Oil 3, 5hrs 150*C. |
(%) |
2 |
| A.S.T.M. Fuel B, 5hrs Room Temp |
|
4 |
| 50% Anti Freeze + 50% distilled water 5 hrs. Room Temp |
|
8 |
|
| Specification Compliance |
| A.S.T.M. F104: 127160 E 62 M3. |
| Typical Applications |
3D-6100 - is a high performance, low density material for use in light to moderate duty applications. Listed below are few of the applications where 3D 6100 is intended to be utilized.
- Exhaust Manifold
- Engine Head Gaskets
- Light Fixtures
- Maintenance Repair Operations
- Pipe Flanges
- Light Duty Transmission
- Availability
- Unit Standard Size
- Roll Width ( Mm) 1220
- Roll Size O.D ( Mm) 200-225
- Roll Weight ( Kg ) 55-65
- Core Size-Id ( Mm ) 75
|
| Availability |
|
Unit |
Standard Size |
| Roll Width |
(MM) |
1220 |
| Roll Size O.D. |
(MM) |
200-225 |
| Roll Weight |
(Kg) |
55-65 |
| Core Size-ID |
(MM) |
75 |
| 3D 6100 is available in thicknesses 0.5 MM, 0.6, 0.65, 0.7, 0.8, 1.0, 1.2 & 1.5 MM. Other special sizes available on request. |
|
| top |
|
| |
| 3D 6300 - Beater Addition Jointing Sheet |
| Material Description |
| 3D-6300 is a high performance, medium density gasket material for use in elevated temperature sealing applications. It is composed of a blend of inorganic fillers reinforced with asbestos fibres in a nitrile binder matrix. 3D-6300 offers excellent sealability & creep relaxation combined with high temperature resistance upto 230°C. This material is available in medium dark grey shade. |
|
 |
| Physical Properties |
| |
Unit |
Typical Value |
| Density |
(gm/cc) |
12 |
| Compressibility at 350 kg/sq.cm |
(%) |
28 |
| Recovery (A.S.T.M. F-36) |
(%) |
35 |
| Tensile Strength (A.S.T.M.F-152) |
(kg/sq.cm) |
80 |
|
| Fluid Immersions |
| WEIGHT INCREASE (A.S.T.M. F-146) |
| A.S.T.M. Oil 3,5 hr, 150° C |
(%) |
37 |
| A.S.T.M. Fuel B, 5hrs room Temperature |
(%) |
32 |
|
|
| THICKNESS INCREASE (A.S.T.M. F-146) |
| A.S.T.M. Oil 3, 5hrs, 150°C. |
(%) |
3 |
| A.S.T.M. Fuel B, 5 hrs, Room Temperature |
(%) |
6 |
| Creep Relaxation, 22 hrs, 100° C. (A.S.T.M F-38 B) |
(%) |
22 |
|
| Specification Compliance |
| A.S.T.M - F-104 - 125150B4E52M4 |
| Typical Applications |
3D-6300 is a high performance, medium density gasket material for use in elevated temperature sealing applications. It is composed of a blend of inorganic fillers reinforced with asbestos fibres in a nitrile binder matrix. 3D-6300 offers excellent sealability & creep relaxation combined with high temperature resistance upto 230°C. This material is available in medium dark grey shade. |
| Availability |
|
Unit |
Standard Size |
| Roll Width |
(MM) |
1150 |
| Roll Size O.D. |
(MM) |
250-275 |
| Roll Weight |
(Kg) |
60-65 |
| Core Size-ID |
(MM) |
75 |
| 3D-6300 is available in thickness 0.5 MM, 0.55, 0.7, 0.75, 0.8, 0.9, 1.00, 1.2 MM & 1.5MM other special sizes available on request. |
|
| top |
|
| |
| 3D 6550 - Beater Addition Jointing Sheet |
| Material Description |
| 3D-6550 is a high performance, medium density gasket material for use in elevated temperature sealing applications. Manufactured from a blend of asbestos fibre, inorganic fillers & nitrile binder, it offers excellent sealability at low flange loads & good resistance to oil, fuels & transmission fluids. This material is recommended for temperature upto 250°C in heavy duty applications & is particularly suitable for head gasket where the material is combined with perforated metal core. This material is available in dark grey shade. |
|
 |
| Physical Properties |
| |
Unit |
Typical Value |
| Density |
(gm/cc) |
1.3 |
| Compressibility at 350 kg/sq.cm (A.S.T.M. F-36) |
(%) |
24 |
| Recovery (A.S.T.M. F-36) |
(%) |
40 |
| Tensile strength (A.S.T.M.F-152) |
(kg/sq.cm) |
120 |
|
| Fluid Immersions |
| WEIGHT INCREASE (A.S.T.M. F-146) |
| A.S.T.M. Oil 3, 5 hrs, 150° C |
(%) |
35 |
| A.S.T.M. Fuel B, 5hrs, Room Temperature |
(%) |
30 |
|
|
| THICKNESS INCREASE (A.S.T.M. F-146) |
| A.S.T.M. Oil 3, 5hrs, 150°C. |
(%) |
4 |
| A.S.T.M. Fuel B, 5 hrs, Room Temperature |
(%) |
7 |
| Creep Relaxation, 22 hrs, 100° C (A.S.T.M. F-38 B) |
(%) |
20 |
|
| Specification Compliance |
| A.S.T.M. F-104 ; 125150 B 4E52M5 |
| Typical Applications |
3 D-6550 due to it's superlative properties is suitable for a wide range of applications. Most of these applications utilise 3D-6550 on a perforated metal core. Compiled below are few of them where 3D-6550 is recommended.
- Cylinder Head Gaskets.
- Transmission Oil Pan.
- Manifold Gaskets.
- Engine Oil Pans.
- Cylinder Covers.
- Gear Boxes.
|
| Availability |
|
Unit |
Standard Size |
| Roll Width |
(MM) |
1150 |
| Roll Size O.D. |
(MM) |
250-275 |
| Roll Weight |
(Kg) |
60-65 |
| Core Size-ID |
(MM) |
75 |
| 3D-6550 is available in thicknesses 0.5 MM, 0.6, 0.7, 0.8, 1.0, 1.2, 1.5MM. Other special sizes available on request. |
|
| top |
|
| |
|
| |
| 3D 610 - Asbestos Mill Board Jointing Sheet |
| Material Description |
| 3D-610 is a stiff & strong asbestos sheet manufactured by wet process using a blend of selected fibres & nitrile binders. This material is widely used for copper clad engine gasket, thermal shields & insulations of electrical devices & home appliances, various heat & acoustic insulation purposes where temperature does not exceed 500°C. This material is available in off-white shade. |
|
 |
| Physical Properties |
|
Unit |
Typical Value |
| Density |
(gm/cc) |
1.10 |
| Compressibility at 70 kg/sq.cm (A.S.T.M. F-36) |
( % ) |
18 |
| Recovery (A.S.T.M F-36) |
( % ) |
28 |
| Tensile strength (A.S.T.M. F-152) |
(kg/sq.cm) |
35 |
| Loss on ignition at 815°C (A.S.T.M. F-495) |
( % ) |
18 |
| Moisture Content |
( % ) |
2.0 |
|
| Specification Compliance |
| A.S.T.M. F-104 : 134000M3 |
| Typical Applications |
3D-610 is primarily used for insulation where fire ratings are important. It finds acceptance as a filler for metal composite gasketing in high heat dynamics such as exhaust manifolds & small stationary engine cylinder head assemblies. Listed below are few of the applications where 3D-610 is recommended.
- Diesel Engines Head Gaskets
- Acoustic Insulation
- Domestic Applications
- Exhaust Manifold
- Electrical Devices
- Thermal Shield
|
| Availability |
|
Unit |
Standard Size |
| Roll Width |
(MM) |
1220 |
| Roll Weight |
(kg) |
60-65 |
| Sheet Size (Packed in Crates) |
(MM) |
1200X1000 |
| Weight/Crate |
(kg) |
100 |
| 3D-610 is available in thicknesses 0.5MM, 0.7, 0.75, 0.8 MM in roll form & 1.0 MM, 1.2, 1.4, 1.5, 1.6, 2.0 MM in sheet form. Other special sizes available on request. |
|
| top |
|
| |
| 3D NA-806 - Non Asbestos Gasket Material |
| Material Description |
| 3D-NA-806 is a high performance medium density material for use as soft gasket manufactured from a blend of cellulose & aramid fibres combined with reinforcing inorganic fillers, imparts an excellent sealing at medium flange loads. It is recommended as replacement to C A F materials in automotive applications. |
|
|
| Test Specifications |
S. No. |
Physical Properties |
units |
Specifications |
| 1. |
Thickness Range |
mm |
0.4-1.5 |
| 2. |
Density |
gm/cc |
1.2-1.3 |
| 3. |
Compressibility at 100 psi |
% |
10-20 |
| 4. |
Recovery |
% |
40 Min |
| 5. |
Tensile Strength |
Kg/Cm2 |
120 Min |
| 6. |
A.S.T.M. Oil 3 (5 Litres at 150°C.)
Weight Increase
Thickness Increase |
% |
25-40
25 Max |
| 7. |
A.S.T.M. Fuel 3 (5 Litres at R.T.) |
% |
25-40
25 Max |
|
| top |
|
| |
|
|
 |
|
